LSL—Load Segment Limit

Opcode Instruction Op/En 64-Bit Mode Compat/Leg Mode Description
0F 03 /r LSL r16, r16/m16 RM Valid Valid Load: r16 ← segment limit, selector r16/m16.
0F 03 /r LSL r32, r32/m16* RM Valid Valid Load: r32 segment limit, selector r32/m16.
REX.W + 0F 03 /r LSL r64, r32/m16* RM Valid Valid Load: r64 segment limit, selector r32/m16

NOTES:

*

For all loads (regardless of destination sizing), only bits 16-0 are used. Other bits are ignored.

Instruction Operand Encoding

Op/En Operand 1 Operand 2 Operand 3 Operand 4
RM ModRM:reg (w) ModRM:r/m (r) NA NA

Description

Loads the unscrambled segment limit from the segment descriptor specified with the second operand (source operand) into the first operand (destination operand) and sets the ZF flag in the EFLAGS register. The source operand (which can be a register or a memory location) contains the segment selector for the segment descriptor being accessed. The destination operand is a general-purpose register.

The processor performs access checks as part of the loading process. Once loaded in the destination register, soft-ware can compare the segment limit with the offset of a pointer.

The segment limit is a 20-bit value contained in bytes 0 and 1 and in the first 4 bits of byte 6 of the segment descriptor. If the descriptor has a byte granular segment limit (the granularity flag is set to 0), the destination operand is loaded with a byte granular value (byte limit). If the descriptor has a page granular segment limit (the granularity flag is set to 1), the LSL instruction will translate the page granular limit (page limit) into a byte limit before loading it into the destination operand. The translation is performed by shifting the 20-bit “raw” limit left 12 bits and filling the low-order 12 bits with 1s.

When the operand size is 32 bits, the 32-bit byte limit is stored in the destination operand. When the operand size is 16 bits, a valid 32-bit limit is computed; however, the upper 16 bits are truncated and only the low-order 16 bits are loaded into the destination operand.

This instruction performs the following checks before it loads the segment limit into the destination register:

If the segment descriptor cannot be accessed or is an invalid type for the instruction, the ZF flag is cleared and no value is loaded in the destination operand.

Table 3-65. Segment and Gate Descriptor Types

Type Protected Mode IA-32e Mode
Name Valid Name Valid

0

1

2

3

4

5

6

7

8

9

A

B

C

D

E

F

Reserved

Available 16-bit TSS

LDT

Busy 16-bit TSS

16-bit call gate

16-bit/32-bit task gate

16-bit interrupt gate

16-bit trap gate

Reserved

Available 32-bit TSS

Reserved

Busy 32-bit TSS

32-bit call gate

Reserved

32-bit interrupt gate

32-bit trap gate

No

Yes

Yes

Yes

No

No

No

No

No

Yes

No

Yes

No

No

No

No

Upper 8 byte of a 16-Byte descriptor

Reserved

LDT

Reserved

Reserved

Reserved

Reserved

Reserved

Reserved

64-bit TSS

Reserved

Busy 64-bit TSS

64-bit call gate

Reserved

64-bit interrupt gate

64-bit trap gate

Yes

No

Yes

No

No

No

No

No

No

Yes

No

Yes

No

No

No

No

Operation

IF SRC(Offset) > descriptor table limit
    THEN ZF ← 0; FI;
Read segment descriptor;
IF SegmentDescriptor(Type) ≠ conforming code segment
and (CPL > DPL) OR (RPL > DPL)
or Segment type is not valid for instruction
         THEN
              ZF ← 0;
         ELSE
              temp ← SegmentLimit([SRC]);
              IF (G ← 1)
                    THEN temp ← ShiftLeft(12, temp) OR 00000FFFH;
              ELSE IF OperandSize = 32
                    THEN DEST ← temp; FI;
              ELSE IF OperandSize = 64 (* REX.W used *)
                    THEN DEST (* Zero-extended *) ← temp; FI;
              ELSE (* OperandSize = 16 *)
                    DEST ← temp AND FFFFH;
              FI;
FI;

Flags Affected

The ZF flag is set to 1 if the segment limit is loaded successfully; otherwise, it is set to 0.

Protected Mode Exceptions

#GP(0)

If a memory operand effective address is outside the CS, DS, ES, FS, or GS segment limit.

If the DS, ES, FS, or GS register is used to access memory and it contains a NULL segment selector.

#SS(0) If a memory operand effective address is outside the SS segment limit.
#PF(fault-code) If a page fault occurs.
#AC(0) If alignment checking is enabled and the memory operand effective address is unaligned while the current privilege level is 3.
#UD If the LOCK prefix is used.

Real-Address Mode Exceptions

#UD The LSL instruction cannot be executed in real-address mode.

Virtual-8086 Mode Exceptions

#UD The LSL instruction cannot be executed in virtual-8086 mode.

Compatibility Mode Exceptions

Same exceptions as in protected mode.

64-Bit Mode Exceptions

#SS(0) If the memory operand effective address referencing the SS segment is in a non-canonical form.
#GP(0) If the memory operand effective address is in a non-canonical form.
#PF(fault-code) If a page fault occurs.
#AC(0) If alignment checking is enabled and the memory operand effective address is unaligned while the current privilege level is 3.
#UD If the LOCK prefix is used.