DIV—Unsigned Divide

Opcode Instruction Op/En 64-Bit Mode Compat/Leg Mode Description
F6 /6 DIV r/m8 M Valid Valid Unsigned divide AX by r/m8, with result stored in AL ← Quotient, AH ← Remainder.
REX + F6 /6 DIV r/m8* M Valid N.E. Unsigned divide AX by r/m8, with result stored in AL ← Quotient, AH ← Remainder.
F7 /6 DIV r/m16 M Valid Valid Unsigned divide DX:AX by r/m16, with result stored in AX ← Quotient, DX ← Remainder.
F7 /6 DIV r/m32 M Valid Valid Unsigned divide EDX:EAX by r/m32, with result stored in EAX ← Quotient, EDX ← Remainder.
REX.W + F7 /6 DIV r/m64 M Valid N.E. Unsigned divide RDX:RAX by r/m64, with result stored in RAX ← Quotient, RDX ← Remainder.

NOTES:

*

In 64-bit mode, r/m8 can not be encoded to access the following byte registers if a REX prefix is used: AH, BH, CH, DH.

Instruction Operand Encoding

Op/En Operand 1 Operand 2 Operand 3 Operand 4
M ModRM:r/m (w) NA NA NA

Description

Divides unsigned the value in the AX, DX:AX, EDX:EAX, or RDX:RAX registers (dividend) by the source operand (divisor) and stores the result in the AX (AH:AL), DX:AX, EDX:EAX, or RDX:RAX registers. The source operand can be a general-purpose register or a memory location. The action of this instruction depends on the operand size (dividend/divisor). Division using 64-bit operand is available only in 64-bit mode.

Non-integral results are truncated (chopped) towards 0. The remainder is always less than the divisor in magni-tude. Overflow is indicated with the #DE (divide error) exception rather than with the CF flag.

In 64-bit mode, the instruction’s default operation size is 32 bits. Use of the REX.R prefix permits access to addi-tional registers (R8-R15). Use of the REX.W prefix promotes operation to 64 bits. In 64-bit mode when REX.W is applied, the instruction divides the unsigned value in RDX:RAX by the source operand and stores the quotient in RAX, the remainder in RDX.

See the summary chart at the beginning of this section for encoding data and limits. See Table 3-25.

Table 3-25. DIV Action

Maximum

Operand Size

Dividend

Divisor

Quotient

Remainder

Quotient

Word/byte

AX

r/m8

AL

AH

255

Doubleword/word

DX:AX

r/m16

AX

DX

65,535

Quadword/doubleword

EDX:EAX

r/m32

EAX

EDX

232 − 1

Doublequadword/

RDX:RAX

r/m64

RAX

RDX

264 − 1

quadword

Operation

IF SRC = 0
    THEN #DE; FI; (* Divide Error *)
IF OperandSize = 8 (* Word/Byte Operation *)
    THEN
         temp ← AX / SRC;
         IF temp > FFH
              THEN #DE; (* Divide error *)
              ELSE
                    AL ← temp;
                    AH ← AX MOD SRC;
         FI;
    ELSE IF OperandSize = 16 (* Doubleword/word operation *)
         THEN
              temp ← DX:AX / SRC;
              IF temp > FFFFH
                    THEN #DE; (* Divide error *)
              ELSE
                    AX ← temp;
                    DX ← DX:AX MOD SRC;
              FI;
         FI;
    ELSE IF Operandsize = 32 (* Quadword/doubleword operation *)
         THEN
              temp ← EDX:EAX / SRC;
              IF temp > FFFFFFFFH
                    THEN #DE; (* Divide error *)
              ELSE
                    EAX ← temp;
                    EDX ← EDX:EAX MOD SRC;
              FI;
         FI;
    ELSE IF 64-Bit Mode and Operandsize = 64 (* Doublequadword/quadword operation *)
         THEN
              temp ← RDX:RAX / SRC;
              IF temp > FFFFFFFFFFFFFFFFH
                    THEN #DE; (* Divide error *)
              ELSE
                    RAX ← temp;
                    RDX ← RDX:RAX MOD SRC;
              FI;
         FI;
FI;

Flags Affected

The CF, OF, SF, ZF, AF, and PF flags are undefined.

Protected Mode Exceptions

#DE

If the source operand (divisor) is 0

If the quotient is too large for the designated register.

#GP(0)

If a memory operand effective address is outside the CS, DS, ES, FS, or GS segment limit.

If the DS, ES, FS, or GS register contains a NULL segment selector.

#SS(0) If a memory operand effective address is outside the SS segment limit.
#PF(fault-code) If a page fault occurs.
#AC(0) If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3.
#UD If the LOCK prefix is used.

Real-Address Mode Exceptions

#DE

If the source operand (divisor) is 0.

If the quotient is too large for the designated register.

#GP

If a memory operand effective address is outside the CS, DS, ES, FS, or GS segment limit.

If the DS, ES, FS, or GS register contains a NULL segment selector.

#SS(0) If a memory operand effective address is outside the SS segment limit.
#UD If the LOCK prefix is used.

Virtual-8086 Mode Exceptions

#DE

If the source operand (divisor) is 0.

If the quotient is too large for the designated register.

#GP(0) If a memory operand effective address is outside the CS, DS, ES, FS, or GS segment limit.
#SS If a memory operand effective address is outside the SS segment limit.
#PF(fault-code) If a page fault occurs.
#AC(0) If alignment checking is enabled and an unaligned memory reference is made.
#UD If the LOCK prefix is used.

Compatibility Mode Exceptions

Same exceptions as in protected mode.

64-Bit Mode Exceptions

#SS(0) If a memory address referencing the SS segment is in a non-canonical form.
#GP(0) If the memory address is in a non-canonical form.
#DE

If the source operand (divisor) is 0

If the quotient is too large for the designated register.

#PF(fault-code) If a page fault occurs.
#AC(0) If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3.
#UD If the LOCK prefix is used.